Back to Blog
How-to Guides 2026-11-18 Grado Labs 0 views

How to Install a Grado Platinum4 Cartridge on Your Tonearm

How to Install a Grado Platinum4 Cartridge on Your Tonearm

A practical walkthrough for mounting the Grado Platinum4: pick the right output version, handle screws and wiring carefully, and confirm alignment before you set tracking force.

Start with the right Platinum4 version

Before you touch a screwdriver, confirm which Platinum4 you actually have. The Grado Labs Platinum4 is a phono cartridge in the Timbre series, and it comes in several output configurations. The standard versions are High-Output and Low-Output. Mono versions are also offered in High-Output and Low-Output, and those mono versions are listed as Special Order / No Returns.

That last detail matters during installation because it changes your return options if you order the wrong one. Check your phono stage or step-up requirements first, then match the cartridge to that setup. If you are unsure whether you need high or low output, resolve that question before mounting, not after.

Platinum4 configurations at a glance

  • Platinum4: The Grado Labs Platinum4 is a phono cartridge in the Timbre series, offered in High-Output and Low-Output versions. Output version is the first compatibility decision; it determines whether the cartridge suits your phono stage before mounting begins.
    Platinum4
    Platinum4
  • Platinum4: Mono versions are also offered in High-Output and Low-Output, and mono versions are listed as Special Order / No Returns. If you play mono records, the mono version is the correct choice, but the no-returns listing means you should verify the configuration before ordering.

Mounting the Platinum4 on the tonearm

The supplied product record does not include a torque specification, screw size, or factory alignment gauge, so use the hardware that comes with your tonearm or headshell and follow the tonearm maker's instructions for those details. The steps below cover the sequence that applies to any standard phono cartridge mount.

  1. Power down and protect the stylus: Switch off the turntable and your phono stage before wiring. Keep the stylus guard on until the cartridge is seated and the arm is balanced.
  2. Attach the cartridge to the headshell: Use the mounting screws supplied with your headshell or tonearm. Tighten evenly so the cartridge body sits square, but do not overtighten.
  3. Connect the four lead wires: Match each colored lead to the corresponding pin on the cartridge. The supplied record does not list a pin diagram, so rely on the markings on your tonearm leads and the cartridge body.
  4. Check alignment before tracking force: Use your preferred alignment protractor to set the cartridge square in the headshell. The supplied record does not include a factory alignment specification, so this is a setup step rather than a product claim.
  5. Balance the arm, then set tracking force: Zero the arm first, then dial in the tracking force recommended for your Platinum4 version. The supplied record does not list a tracking force range, so confirm the figure from the cartridge documentation before playing a record.

Cartridge screws and wiring: what to watch

The Platinum4 record does not specify screw length or wire gauge, so the safest approach is to use the hardware that came with your tonearm and to treat the cartridge body as the fixed reference point. A few practical checks prevent most installation problems.

  • Screw length: Screws that are too long can contact internal parts. Test-fit them through the headshell before the cartridge is in place.
  • Lead orientation: Keep the four colored leads in the correct order. Reversing left and right or hot and ground is the most common wiring mistake.
  • Body clearance: Confirm the cartridge body clears the record surface through the full arm travel before you lower the stylus.

Alignment and first-play checks

Grado Platinum4 alignment follows the same logic as any cartridge: the stylus should track squarely in the groove across the record. Because the supplied record does not include an alignment geometry or overhang figure, use the protractor and tonearm instructions you already trust. After alignment, set tracking force and anti-skate, then play a record you know well and listen for channel balance and tracking stability.

If something sounds wrong, stop and recheck the wiring and alignment before adjusting anything else. The Platinum4 record does not list a break-in period or a recommended tracking force range, so avoid inventing a number; use the documentation that came with the cartridge.

What the Platinum4 record confirms for your setup

  • Platinum4: The Platinum4 is offered in High-Output and Low-Output versions, and mono versions are available in both output levels. This is the confirmed configuration choice you need to make before mounting; it affects compatibility with your phono stage.
  • Platinum4: Mono versions are listed as Special Order / No Returns. If you are installing a mono Platinum4, confirm the order details before mounting, because returns are not available on those versions.

Related Articles

Customer Service
Home
Products
Cart
Profile